Are you looking for ways to make stamped concrete non-slippery? If yes, then you’re in the right place. Stamped concrete is one of the best options when it comes to sprucing up your home, driveway or patio.

But many people face issues with slippery surfaces when using stamped concrete, leading them to wonder how they can improve traction and safety on their hardscape surfaces.
In this post, we provide an overview of how to make stamped concrete not slippery and what stamped concrete is followed by a comprehensive dive into effective steps to reduce slipping on all types of stamped concrete paving projects. Read along for all the essential info you need about making the backed surface less slippery!
Why Should You Make Stamped Concrete Not Slippery?
Stamped concrete offers a wide range of benefits, including long-term durability and lower maintenance costs. However, it can also be slippery when wet if the proper treatments haven’t been applied to make it non-slippery.
Slipping on stamped concrete surfaces can lead to serious injuries such as muscle sprains and broken bones. Therefore, it is important to make sure that your stamped concrete surfaces are as non-slippery as possible so that you can avoid any potential accidents.
Essential Materials
Below are some of the essential materials you’ll need to make your stamped concrete not slippery:
Skid-resistant Sealer
You’ll need an anti-slip sealer for your stamped concrete, as it provides a protective barrier and makes the surface less slippery. Choose a high-quality skid-resistant sealer that is specifically designed to reduce slipping.
Acid Etching Solution
An acid etching solution can help to slightly roughen the surface of the concrete, making it less slippery.
Grit or Sand Additives
You can also add grit or sand additives to your sealer to make the surface even more non-slippery. These materials will fill in any small crevices and provide additional traction on the surface.
12 Step-By-Step Process on How to Make Stamped Concrete Not Slippery
Step 1: Clean and Prep the Surface

Before you begin, make sure that the surface is clean by removing any dirt or debris with a pressure washer. If the surface is severely stained or worn, you may need to bull float it using a heavy-duty concrete float.
But be sure not to over-float the surface as this can cause it to become slippery. It is also important to make sure that the surface is completely dry before you move on to the next step.
Step 2: Apply an Acid Etching Solution
Once the surface is clean and dry, you can apply an acid etching solution to slightly roughen it up. This will help create a safer non-slip environment on your stamped concrete surface by filling in any small crevices. It is best to follow the directions provided by the manufacturer when applying this solution.
Step 3: Rinse the Surface
Once you have applied the acid etching solution, it is important to rinse off the excess with water.
This will ensure that all of the residues are removed and that your surface won’t become slippery due to an accumulation of material on its surface. That said, be sure to use a hose with low pressure and avoid using too much water.
Step 4: Allow Time to Dry
After rinsing the surface, you will need to wait to dry completely before continuing. This usually takes around 24 hours or so, depending on the temperature and humidity levels in your area.
But it is essential to give the surface plenty of time to dry so that the sealer can properly adhere. It is also a good idea to cover the surface with plastic or a tarp during this time, as that will protect it from any moisture or dirt.
Step 5: Apply Skid-Resistant Sealer

Once the surface is dry, you can apply a skid-resistant sealer that is specifically designed to reduce slipping on stamped concrete surfaces. Be sure to follow all of the instructions provided with your sealer and be sure not to miss any spots as this could result in an uneven application. With this type of sealer, you will usually need to wait around 24 hours before moving on to the next step.
Step 6: Add Grit or Sand Additives (Optional)
If desired, you can add grit or sand additives to your sealer for additional non-slip protection. This is an optional step, but it can help to make the surface even less slippery.
But be sure to follow the manufacturer’s instructions on how much of these materials to add. Otherwise, you could end up with an uneven application or even a slippery surface.
Step 7: Use a Roller or Sprayer
Once you have applied the sealer and any desired additives, use a roller or sprayer to evenly distribute the product across the entire stamped concrete surface. It is important to ensure that the sealer covers all of the crevices and edges, as this will provide better protection from slipping. If desired, you can use a brush or sponge to get into smaller areas.
Step 8: Allow Time to Cure
Allow time for the sealer to cure before using the stamped concrete area as this will ensure that it fully adheres and provides maximum non-slip protection. This usually takes around 24 hours or so, but be sure to follow the curing times provided by the manufacturer.
However, if the area gets wet during this time, it is important to allow an additional 24 hours for drying before using the surface.
Step 9: Check for Uneven Areas
Once the seal has cured completely, check for any uneven areas that may require touching up with another coat of sealer. It is important to make sure that the sealer covers all of the crevices and edges, as this will help prevent slipping. If needed, apply another coat of sealer to even out the surface.
Step 10: Apply an Additional Coat (Optional)
If desired, you can apply an additional coat of the sealer to further reduce slipping. This is entirely optional but it may provide extra protection in areas that are particularly slippery.

Because of this, it is important to test the surface for slip resistance after each coat. If the area is still too slippery, you may need to add more grit or sand additives or apply another coat of sealer.
Step 11: Allow Time to Cure Again
Allow time for the second coat of sealer to cure before using the stamped concrete area as this will ensure that it fully adheres and provides maximum non-slip.
This is usually around hours or so, but be sure to follow the curing times provided by the manufacturer. If the area gets wet during this time, it is important to allow an additional 24 hours for drying before using the surface.
Step 12: Enjoy Your Non-Slippery Stamped Concrete Surface!
Once all have been completed, you’re all set and ready to enjoy your non-slippery stamped concrete surface! Now you can rest assured that your stamped concrete won’t be slippery and will provide a safe environment for you and your family to enjoy.
Remember to test the surface for slip resistance every now and then. If you notice any slipping, may need to apply another coat of sealer or additional non-slip additives.
We hope this article on how to make stamped concrete not slippery has been helpful in providing you with the information you need. If you have any more questions or concerns about keeping your stamped concrete surface safe and non-slippery, contact a professional for help. Good luck!
Do You Need to Use Professionals?
While following the steps outlined in this article should help make your stamped concrete surface less slippery, it is often recommended to contact a professional for the best results.
A professional can inspect your surface and provide you with the safest and most effective solution. Additionally, they may be able to suggest other solutions such as adding an anti-slip coating or changing the texture of the stamped concrete surface.
So if you are unsure about how to proceed or would like to further reduce slipping on your stamped concrete surface, contact a professional for advice.
Frequently Asked Questions
Q: How Often Should I Apply the Sealer?
A: It is recommended to reapply the sealer every 2-3 years or as needed. If you live in a particularly wet or cold climate, it may be necessary to reapply the sealer more frequently.
Q: Does Stamped Concrete Need to Be Sealed?
A: Yes, it is recommended to seal stamped concrete surfaces to prevent moisture penetration, reduce staining and fading, and provide non-slip protection.
Q: Are There Non-Slip Coatings I Can Use for Stamped Concrete?
A: Yes, there are many non-slip coatings available that can be used on stamped concrete surfaces to provide even more protection against slipping. Be sure to follow all of the instructions provided with the product and contact a professional if you have any questions.
Q: Will a Non-Slip Coating Make the Amped Concrete Less Attractive?

A: No, there are non-slip coats designed to enhance the look of concrete while providing protection against it. Be sure to do your research and select the coating that best suits your needs.
Conclusion
It is clear that making stamped concrete non-slippery requires preparation and the application of the right materials. There are a few options for this, from using a sealant to using a grit additive. If done properly, you will be able to enjoy the look of your stamped concrete while avoiding any dangerous slip-and-fall accidents.
Remember to wear protective gear when doing this work, and consider hiring a professional if you feel uncomfortable tackling this type of job yourself. Overall, these steps on how to make stamped concrete not slippery can help make sure that your stamped concrete surfaces remain safe and attractive.
Thanks to the right kind of preparation and materials, it is possible to make stamped concrete not slippery so users can enjoy its beauty without putting themselves in harm’s way.